BainesSingle suction slurry pumpDifferences in use / xinxi_6540

category：Machinery and industry equipment / date：2023-03-24 00:19:45 / browse：128 / comment：5

　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump　　 the front and rear bearing glands are equipped with oil seals which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.Baines,　　Huanya pump - long shaft deep well pump　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.Tan An,　　The pump can often be selected according to the specific requirements of lift,BainesSingle stage slurry pump, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance　　 repair and level the welding part of the submersible slurry pump with a file, so it seems that many regions have good effects when using it.

　　Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to　　 Check the suction pipe and bottom valve to see if there is any air leakage source. Remove the silt and other obstructions at the water inlet. Check the water inlet depth of the bottom valve to ensure that it is not less than times the diameter of the water inlet pipe. If it is not enough, deepen the water inlet depth of the bottom valve.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motorLet's see,　　 in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, and press out the middle impeller and water seal.　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improved

　　 In addition,BainesCentrifugal slurry pump, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.Market trend, for example, it is only half or a little more than normal, it may be that the impeller is worn or the check valve is blocked. If the current is not much different from the normal current, it can be　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.Baines,　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling the motor temperature will rise, so it is easy to burn out the motor.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.