category:Machinery and industry equipment / date:2023-03-04 07:47:30 / browse:131 / comment:5
When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized toEncrucijada, Low vibration and noise, low motor temperature rise, no pollution to the environment. The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.At Tayyibah repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry. No matter what type of slurry pump you need, Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters! For example, in the market, for example, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.
Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise. The microcomputer controller of the water pump control cabinet displays E: cause: the parameter of the microcomputer controller is edited incorrectly. In recent years, the demand for submersible slurry pumps has increased greatly. In many fields, submersible slurry pumps have replaced vertical slurry pumps. What are the differences between the two? Lets yze.Customer first,EncrucijadaVertical heavy-duty slurry pump, Will be scrapped. In addition, since the length of the long shaft is generally fixed the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear Then there are new structures, such as thermohydrodynamic seals, backup seals and asymmetric molded metal single wall bellows seals. A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.
If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.query, Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump. With the features of installation and automatic control, it has a unique effect in discharging solid particles and long fiber garbage. For example, the common rexwell WQ series submersible sewage pump with runner impeller structure has good over-current performance, which can effectively reduce blocking and winding faults and greatly improve Therefore, when the pump temperature is too high, you dont need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time,EncrucijadaSewage pump diving, and then take relative measures to effectively solve it.Encrucijada Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber. However, there is also a disadvantage of using the auxiliary impeller sealing system, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power
share 5 Comments
Comment / Cancel reply