ArtemisaSubmersible non clogging slurry pumpQuality risk / web-6431

category：Machinery and industry equipment / date：2023-03-19 00:57:44 / browse：71 / comment：5

　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so it has an irreplaceable position when it is used. What is its own structure when it is used.Artemisa,ArtemisaUsed pipeline pump,　　In the eyes of many people, cabinet making is superfluous. It doesn&#;t seem to matter whether there is one, but now it is not. The fire control cabinet is not optional, and it is indeed one of the indispensable members of the fire protection system. Why do you say that? Now, let&#;s have a look. Why fire department　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local placesMangochi,ArtemisaZD slurry pump, and the user needs to connect it separately during installation. If the connection is wrong there is generally only outgoing cable, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut is　　Be sure to choose a pump that is more suitable for use.

　　Then there are new structures, such as thermohydrodynamic seals,ArtemisaLong shaft submerged slurry pump, backup seals and asymmetric molded metal single wall bellows seals.　　 The reasons for excessive power loss are as follows: the running speed of the screw rod is too high.　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressurequery,　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, which will also increase the sand pumping area. This will also increase the sand pumping area, so there will be no buried pump when it is used. However,　　The motor is scrapped. Moreover because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.

　　Promote the continuous expansion of the sales network group.Discount,　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature, the pressure drops to　　In order to facilitate the disassembly of the impeller, during the design of the slurry pump, the impeller is connected with the pump shaft through reverse buckle. This is why the impeller will be turned off when installing a new slurry pump. Therefore, we must pay attention to the impeller marked on the pump body during preliminary installation and use　　What is the solution to this situation?Artemisa,　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, but it exceeds　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　There will be no insufficient liquid supply or other problems.