category：Building materials / date：2023-02-02 08:40:03 / browse：120 / comment：5
Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension,GuaranWelding video of galvanized square pipe, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, it can reflect that the square tube is good. On the contrary, if the surface is not goodSteel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.Guaran,The standard number of spiral square pipe (standard of the Ministry of petroleum) for low pressure transmission is syt-. The representative materials are qbqb and other carbon steel materials. It is mainly used for low-pressure transmission of water, oil, natural gas,GuaranHow much is a galvanized pipe, heating and other pipelines.The other is designed with deformation angle which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.Amiens ,The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright., cold drawn tubes tubes, etc. Hot rolled seamless tubes are produced on the automatic precision tube precision tube rolling mill. The solid tube blank is cut into the required length by removing surface defects, centering on the end face of the perforated end of the tube blank, and then sent to the heating furnace for heating. It is perforated on the piercing machine. At the same time, it rotates and advances continuously under the action of roll and plug, A cavity is gradually formed inside the pipe blank, which is called the rough pipe, and then sent to the automatic pipe mill for continuous rolling. After the wall thickness is adjusted by the whole machine and the diameter is determined by the sizing machine to meet the specification requirements. The continuous pipe mill is more advanced in producing hot-rolled seamless steel pipe. If you want to obtain seamless pipe with smaller size and better quality, Cold rolling and cold drawing must be adopted, or the combination of cold rolling and cold drawing is usually carried out on the roll mill. The seamless pipe is rolled in the annular pass composed of variable section circular hole groove and fixed conical plug. Cold drawing is usually carried out on the single chain or double chain cold drawing machine, that is, the heated pipe blank is placed in a closed cylinder, and the perforated rod and rod move, This method can produce steel pipe with small diameter. In the building materials industry the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. We need to understand the various characteristics of steel pipes. However, in the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. The various characteristics of steel pipe need to be understood by everyone. However, due to the of steel pipe and other raw materials, the storage of steel pipe needs specific conditions.Section shape classification of large-diameter qb square tube square tube is classified according to section shape: simple section square tube & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Flower shaped square pipe, open square pipe, corrugated square pipe, large-diameter qb square pipe surface treatment classification square pipe is divided according to surface treatment: hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe, acid pickling square pipe, large-diameter qb square pipe purpose classification square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tool equipment, machinery industry, chemical industry, steel structure, shipbuilding, automobile, steel beam and column, special purpose, large-diameter qb square tube wall thickness classification, large-diameter qb square tube according to wall thickness Classification & mdash& mdash; Super large diameter qb square pipe, large diameter qb square pipe and thin-wall large diameter qb square pipe rectangular pipe are the names of square pipe and QB square pipe, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Usually pieces per bag. Qb square pipe, also known as square and rectangular cold-formed hollow section steel, is referred to as square pipe and rectangular pipe, code f and j respectively. The allowable deviation of wall thickness of qb square pipe shall not exceed plus or minus % of nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of wall thickness when the wall thickness is greater than mm, except for the wall thickness of corner and welding joint area.
Superior square tubular steel (both P and s ≤ .%)After, the workpiece forms an oxide film with a fixed thickness and presents various colors. Chemical oxidation method is to form various film colors in a specific solution at temperature and time; Because of the law & rdquo; More, but to maintain the color of the product, the reference electrode must be used. Electrochemical method is to form the color of chloride film with fixed thickness in specific electrolyte at temperature, voltage and time. This process is mature and widely used. Ion implantation method is to vaporize ions in vacuum and deposit them on the surface of qb square tube, such as watch case on the market. The golden color of watch strap adopts this process technology, which is suitable for mass production. The process of gas phase cracking is more complex and less used in industry. Square tube has long been widely used in mechanical industry. When the square pipe is cut automatically, when the square pipe is hoisted to the gas cutting platform, the distance difference between the two ends of one side of the pipe and the guide rail shall be adjusted within mm. During semi-automatic cutting, the guide rail shall be placed on the plane of the cut pipe, and then the cutting machine shall be placed on the guide rail gently.In the square tube production process of welding before forming, the forming is mainly completed by the sizing frame. The sizing machine is generally a two high mill, including horizontal frame and vertical roll frame. At present, there are mainly two kinds of square pipe pass design: one is the horizontal frame is designed according to the box hole, and the other frames are approximately rectangular holes. The pass section is composed of circular arc. Professional projects include: square pipe square pipe, seamless square pipe, galvanized square pipe, galvanized pipe and other related businesses. Please welcome merchants who want to have this business. And the arc radius increases frame by frame, The fillet radius of the joint between the side wall and the bottom of all pass patterns is equal to the fillet radius of the finished section. The total elongation coefficient of the square tube is about , which is mainly distributed on the flat roller. The deformation of the vertical roller is very small, and its function is to press down the short side of the square tube. With this design, the calculation is complex and the calculation value is not accurate enough. It is necessary to constantly correct the pass circumference.Economic management,For gas transmission: gas,GuaranHow much is 50 galvanized square tube, steam and liquefied petroleum gas.B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.Comprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C)； (d) Q( B)； (e) Q.
Comprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C)； (d) Q( B)； (e) Q.quality,Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )The surface compressive stress characteristics of the square tube will be obtained after isothermal quenching.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Guaran, core rod and casing for diamond core drilling.Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, sampling quantity, hot-rolled square tubes can be sampled in batches according to the rolled root array.
share 5 Comments
Comment / Cancel reply