there are aluminum oxide, melamine and piano paint.burnaby, If there are hard objects, check the ground hardness, which shall not be lower than MPa. Smell: whether the product has a chemical smell that irritates people. The big smell is likely to be that the limit of harmful substances exceeds the standard or the printing layer on the surface of floor leather releases toxic gas.Saryozek,In order to prevent local fading due to frequent sunlight exposure, it is best to hang curtains to turn direct light into diffuse light, which is conducive to prolonging the service life of the floor. Pay attention to the fact that hard substances such as metal sharps and shoe staples are easy to scratch the surface of the worn lacquer cloth. Avoid cigarette butts, boiled water and hot objects above ℃ from directly contacting the plate surface. Prevent burning marks and scalding marks. Do not press the surface with rubber pads for a long time,In case of indentation, it is difficult to remove. Although the ground lacquer cloth is flame-retardant and self extinguishing, it will decompose harmful gases at high temperature which will suffocate if inhaled too much. First, pursue foreign goodsCommon cost methods for solid wood flooring are as follows: Easy to clean: medical treatment is simple, no stains, easy to clean.The surface paint of solid wood composite floor is very good, with good wear resistance, without excessive vitality maintenance.According to statistics, the solid wood composite floor prepared for the sales market will not be waxed within years, and the wind color of automobile coating will also be maintained.This is obviously compared with the maintenance of solid wood flooring.category:Building materials / date:2022-05-23 00:14:38 / browse:355 / comment:6
SPC floor is considered as a new generation of floor materials, which is characterized by extremely stable, high performance, complete waterproof high-density sales core and pressure mark;It can be easily installed on different types of ground bases, concrete, ceramics or existing floors.Three layer solid wood composite floor.When asked about the service life and wear resistance of SPC floor in the message area of the message board, it is often mentioned to take out artifact such as fruit knife or key and scratch on the surface of SPC floor. If there are scratches they are classified as non wear resistance.In fact, the national wear resistance test of PVC latch floor is not simply to scratch on the surface with artifact, the wear-resistant layer on the floor surface is damaged and exposed to the speed of rural grass-roots.The rotational speed of this connection point is an index value considering the wear resistance of PVC latch floor.For example, the minimum speed of national composite floor is rpm.Therefore, the wear resistance of PVC latch floor is professionally measured by the national testing center.Honesty and mutual benefit, Considering from the elements of economic development: strengthening is better than solid wood.If you buy solid wood, the quoted price is generally the price of bare board, plus the price of installation and spare parts. In terms of comfort,burnabyCan SPC floor be used outdoors, strengthening and solid wood are better than ceramic tiles, because they are warm for many days and cool in summer.The surface coating of piano paint is actually the paint used on the surface of solid wood floor for laminate floor. It is only bright paint. The wear resistance of this coating is far from that of aluminum oxide surface. Its wear resistance is low, and solid wood floors are developing towards high wear resistance. Unless you like the coating of this surface.The thickness of SPC floor is mainly selected according to personal needs.Of course, the floor thickness affects the floor price, and the service life will be different, the better. We need to select according to whether the installation will affect the door closing or other s;Whether the overall effect after installation will be uncoordinated;Material budget and other aspects to select the most appropriate floor thickness.
Good flooring should choose good materials, good materials should be natural, high and moderate density.Some people think that the higher the density of wood-based panel, the better. In fact, it is not. If the density is too high, its water absorption and expansion rate is also high, which is easy to cause size change and lead to floor deformation.Secondly, we should rely on advanced flooring production lines and equipment and rigorous technology to produce first-class flooring.Judging the quality of the floor can also be measured from the quality inspection certificate and other honorary certificates such as 'national quality inspection free products', 'ISO quality system certification',burnabyFloor waterproof and leakage repair, 'ISO environmental system certification', because the acquisition of these honors must refine the results of an enterprises operation.Product range, About strengthening the floor. All standard SPC floors must be certified by IS international quality management system and ISO international green environmental protection product certification.The surface texture of solid wood floor is clear and natural, and there is no obvious color difference on both sides.Medium and low grade solid wood floors indicate that cracks may occur.If the crack is not a problem between textures,burnabyHow to deal with the large gap of wooden floor, there will be some hidden dangers if the crack passes through the texture.burnaby, In terms of foot feeling, solid wood is better than reinforcement. According to national industry standards, all solid wood is mm thick, and wood keel ceiling is selected for installation, so the upper foot is better than mm thick reinforcement plate.How to distinguish true and false solid wood flooring?As the wear-resistant layer on the surface of the laminate floor has good wear resistance, compression resistance, impact resistance fire resistance, flame retardancy and chemical pollution resistance, in daily use, it only needs to be cleaned with a twisted dry rag, mop or vacuum cleaner. If the floor is greasy and dirty, wipe it with a cloth stained with detergent.The flame retardant grade is B, and the indoor formaldehyde meets the national industry standard.
share 6 Comments
Comment / Cancel reply