category：Building materials / date：2023-03-27 18:16:48 / browse：138 / comment：4
The side length of I-beam is small and the height is large, so it can only bear the force in one direction.The utility model has the advantages that the axial force of the roll is small, the axial movement is small, the working inclined plane is not required, and more passes can be matched under the condition of a certain length of the roll body.Milaguana,The preparations for the construction of high-speed reinforcement mesh include the preparation and inspection of raw materials, the inspection and acceptance of the lower layer of the pavement, and the preparation of construction equipment and engineering machinery.When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Pargas,Defects of alloy pipe and solutions: Small longitudinal crackH-shaped steel groove is deep and thick, and can withstand forces in two directions.
Classification introductionCharacteristics and application of galvanized pipea. In the forming process, the thick steel plate has uniform deformation, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size,MilaguanaDN25 welded pipe more than one meter, specification and model of diameter and wall thickness, especially in the production and manufacturing of steel structure design grade thick wall pipe, especially medium diameter small thick wall pipe, which has incomparable advantages of other processing technologies, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution ~ times of water cleaning, the solution temperature is ~ ℃ and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, and the solution time is min. Then dry.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties chemical properties, weldability and structural size.
With the development of steel structure buildings, only I-beam is not enough, that is, thickened I-beam, which is easy to lose stability for load-bearing columns.offer, Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, that is, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole,MilaguanaPrice of 15CrMoG alloy pipe, etc.This phenomenon is affected by cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition,Milaguana150mm welded pipe weight per meter, the greater the plastic deformation non-uniformity and residual stress caused by thermal stress during cooling.Plan scheme : Martensitic chromium alloy pipe and chromium alloy pipe with Cr composition exceeding %, without high carbon steel and high chromium alloy pipe. The aqueous solution contains % sodium cyanide % ~ % (volume ratio), the solution temperature is ~ ℃, and the solution time is min.Milaguana,At the same height, light I-beam has narrower legs, thinner waist and lighter weight than ordinary I-beam. No. - is large I-beam, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications, dimensions and relevant standards.Alloy tube is widely used in our daily life, which provides us with great assistance. So what industries are alloy tubes applied to? Let&#;s follow the steps of all manufacturers and have a look together:X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.
share 4 Comments
Comment / Cancel reply