category：Machinery and industry equipment / date：2023-03-13 07:43:36 / browse：145 / comment：4
add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is full Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.Columbia, tailings transportation, various tailings ore, pulp, pulp, coal slurry, slag, slag treatment, etc. Work, no noise and vibration, and the site is cleaner.Guidonia Montecelio, Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, it is actually quite simple The pump can often be selected according to the specific requirements of lift,ColumbiaCirculating hot water pipeline pump, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.
fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit. Whether the pipeline pump can absorb water and whether the pipeline pump has self-priming depends on the model of the pipeline pump. Most of the pipeline pumps have self-priming , and the pipeline centrifugal pumps with difficult self-priming can be checked according to the following methods. For longer use It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.A complete range of products, In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump,ColumbiaSubmersible pump can pump sewage, but it is adjustable. During normal operation the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation. First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so
If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.new product, Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurry Check the oil quality of the oil chamber every six months to see if there is any leakage, and force replacement; Check the impeller for wear and determine whether it needs to be repaired and replaced. Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energyColumbia, Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump,ColumbiaFire deep well pump, such as sand pumping on board, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pump When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment
share 4 Comments
Comment / Cancel reply