category：energy / date：2022-06-08 01:09:05 / browse：533 / comment：6
Frequently observe the operation state of the heart compressor of the cold storage equipment and its exhaust temperature. During the season change operation, pay special attention to the operation state of the system and adjust the liquid supply and condensation temperature of the system in time.We should implement regular maintenance and daily maintenance, professional cold storage installation, installation of cold storage, cold storage construction, fruit preservation cold storage, medical cold storage, large quantity, excellent quality and low price fire resistance - Waterproof - high temperature resistance, safe and reliable strong and durable,PickeringOf cold storage installation enterprises, and maintain the operation rate of the compressor.Pickering,Daily maintenance and management of fruits after Warehousing: timely the temperature and humidity in the cold storage, strictly control the temperature in the cold storage, timely eliminate the bad gas in the cold storage, and adjust the temperature and humidity of the cold storage according to the different requirements of different fruits on the storage environment. If long-term drying will affect the color of the fruit, consider using a humidifier to adjust the humidity in the cold storage.Feasibility of the design scheme: the design of the quick-frozen warehouse can not be taken for granted. Many restrictive factors should be considered. In practice, a reasonable design scheme should be given according to local conditions. For example, the large-scale quick-frozen warehouse I built for my family should be refrigerated with ammonia in theory, because the refrigeration capacity of ammonia refrigeration is large,PickeringInstallation of aluminum bar in cold storage, and I found that it is cheap to replicate cold through actual field investigation.Sumgate,During the early operation of the refrigeration unit, carefully observe the oil return of the compressor and keep it clean. If it is found that the oil level is not clean enough or the oil level drops, replace it with new oil in time, so as to avoid bad compressor and reduce the service life of the compressor.Polyurethane refrigeration board uses light polyurethane as the internal material of refrigeration board. The advantage of polyurethane is very good heat insulation. The exterior of the cold storage is composed of SII, PVC color steel plate and stainless steel plate. The advantage of this is that it can prevent refrigeration, because the temperature difference inside and outside the board is large, and the temperature will disperse, which makes refrigeration more energy-saving and improves the working efficiency of refrigeration.Whether the parameters of refrigeration equipment are consistent. When the cold storage leaves the factory, the temperature and temperature difference parameters of the cold storage shall be customized according to the user's requirements. After understanding the technical parameters of the cold storage, set the parameters on the refrigerator. During use, the air humidity is high and the defrosting interval is long. The common cold storage boards of cold storage include mm, mm, mm, mm and mm polyurethane thermal insulation boards, color steel tiles, stainless steel plates, salt thick steel plates, embossed aluminum plates, polyurethane spraying, etc. on both sides or single and double sides, more general color steel tiles are produced and processed into hidden grooves, which have light weight, high compressive strength, good fire resistance, corrosion resistance and aging resistance, The cold storage board is simple and convenient to assemble, and is a wide range of raw materials selected for the heat insulation and heat preservation of the cold storage. The cost of stainless steel plate and salt plate increases, and it is also easy to deform and damage the appearance.
The drainage at the outlet of the cooling fan, the drainage of the volatile cooler and the road drainage of the refrigerated warehouse storing food or drinks shall not be immediately connected with the sewage and wastewater pipeline system software, but indirect drainage shall be adopted. For the flushing (thawing) water drainage of each layer in the double-layer cold storage, an exhaust valve equipment shall be set in front of the main riser for flushing (thawing) water drainage.Regularly maintain whether the connecting pipes on the connecting pipes and valves of the refrigeration unit are firm and whether there is refrigerant leakage. The way of leak detection is to use sponge or thin cloth with detergent, foam, and then evenly coated in the area to be leaked, and observe for a few minutes. If water leaks, bubbles will appear. Mark the leaking area, and then tighten or gas cut it.When hot ammonia defrosting or electric defrosting is selected as the cooling fan professional cold storage installation, cold storage installation, cold storage construction, fruit preservation cold storage, medical cold storage, safety, environmental protection and economy! The products are exported to foreign countries and are deeply trusted. Defrosting and drainage can be discharged immediately. Electric heat tracing and insulation can be selected for the defrosting and drainage pipeline of the warehouse location.install, the warehouse body can be divided into small warehouse body and large warehouse body. The small warehouse body is basically a combined cold storage assembled with warehouse plate. The large warehouse body is mostly a civil cold storage. The assembled or constructed warehouse body is generally required to be flat, without hollow feeling, load-bearing, antifreeze, moisture-proof etc.The product shade warehouse is a warehouse location below ℃ and the sun cannot be straight. The humidity is % ~ % relative humidity, and there are corresponding strict requirements for the wall, ceiling, ventilation, and can monitor and record the temperature and humidity in the storage area.The overall construction achievements of the cold storage project have been put into use, and the service life can reach years.
The cold storage shall be regularly overhauled and maintained, so as to reduce the failure rate of the refrigeration unit and achieve good refrigeration effect.plan,Compression refrigerator is commonly used. It is mainly composed of compressor, condenser, throttle valve and evaporation pipe. The evaporation pipe is installed in the refrigeration warehouse. When the liquid coolant passes through the evaporation pipe, shape and position tolerances are in micron level; No exhaust valve poor off design performance; The working chamber is not easy to implement external cooling, and the heat in the compression process is difficult, so it can only compress the gas with small adiabatic index or internal cooling; Large displacement scroll refrigeration unit is difficult to realize. The receiving teeth are high, the displacement is large, the diameter is large, and the unbalanced rotation mass increases.Install the electric control system. The electric control system of the cold storage mainly includes electric controller, electric door, lighting and other electrical equipment in the cold storage. The power supply of the cold storage is required to be stable phase line, and the power supply or backup power supply can be used as required. The circuit shall have reasonable discharge and corresponding protective measures.Pickering,In the cold storage project, the selection of cold storage is related to the overall operation of cold storage in the future. The selection of high-quality cold storage is conducive to the use and maintenance of cold storage. This requires us to inquire more about the warehouse board for cold storage engineering. Before the construction of cold storage project, we should first realize the temperature requirements of cold storage and the importance of cold storage to cold storage. Because the cold storage project has high environmental requirements such as temperature, attention should be paid to the performance and material of the cold storage board when selecting the cold storage board.According to the size and nature of the cold storage area and in combination with local regulations, the construction form of food cold storage warehouse is to determine the plane layout based on the site, whether it is a single-layer or double-layer warehouse, and the structure is the selection of steel structure or reinforcement solidification. Cold storage capacity, refrigeration product stacking, etc. are used to determine the size and location of the cold storage room, so that it can become a whole.Pay attention to the energy saving of the lighting system: the lighting of the cold storage should be considered comprehensively according to the area, height and warehouse temperature of the cold storage on the basis of safety, science and rationality, from the perspective of energy saving and environmental protection. The lighting in the cold storage is concentrated in the working area.
share 6 Comments
Comment / Cancel reply