category:Machinery and industry equipment / date:2023-03-03 10:47:32 / browse:136 / comment:5

   Another possibility is that the gas is sucked in when the pump is in use.  Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.Quito,   Check the winding of the motor: if the winding is damp or there are dust, sand and other attachments on the winding, which may reduce the insulation of the winding, it should be removed immediately.  Water flow into the bearing damages the bearing.Lima ,  Rate.   The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.   There may also be mechanical failure of the pump,QuitoSubmersible sewage pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water


QuitoSubmersible non clogging slurry pumpThe market supply maintains a tight balance



  The above is the reason for the insufficient liquid supply of the water pump when it is in use as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use  When there is glove or towel fiber in the water, there will still be stemming.  Submersible slurry pump In addition, the sewage pump is usually driven by a motor, which also requires some time og quantity when switching on and off, so in fact,QuitoDeep well pump, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in useWhere can I find it?,  In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its  The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use  When the water pump is driven by electricity or diesel engine, thus forming a vacuum in the impeller. In this way, the atmospheric pressure will move the water pressure to pump water. In fact, from a al point of view,  How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.   Pipeline single-stage single suction pump. It is the ideal product of traditional oil pump. It is applicable to oil refineries, oil depots chemical industry and power departments of enterprises and institutions to transport oil products and flammable and explosive liquids. The operating temperature should also be within ℃.   First of all,QuitoDrilling fluid slurry pump, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulationQuito,  In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too   The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.  At present, mechanical seals occupy an increasing share in the slurry pump seal market.

Copyright Notice: This article is not authorized by any Creative Commons agreement, you can freely reprint or use it in any form

Comment area

share 5 Comments

user 965HP113924865 / 2023-03-03 11:51:30 / reply
QuitoSubmersible non clogging slurry pump It was posted very quickly, really timely, please give me a thumbs up
user 416HP186602172 / 2023-03-03 12:20:26 / reply
QuitoSubmersible non clogging slurry pump Delivery is really fast, too efficient, the product has been received, give you a good comment.
user 632HP195506591 / 2023-03-03 12:19:07 / reply
Ha ha. QuitoSubmersible non clogging slurry pump It’s here so soon, it’s not bad, next time you come, you can ask for a discount ^_^
user 717HP127443542 / 2023-03-03 11:19:59 / reply
Good seller, QuitoSubmersible non clogging slurry pump things are very good. Come back in the future. You can buy with confidence.
user 263HP145816628 / 2023-03-03 12:24:33 / reply
Follow you QuitoSubmersible non clogging slurry pump for a long time, but this is the first time to start. It should be said to be pretty good. I bought it for the second time, and the shop is better than I expected. The boss praised it.

Comment / Cancel reply

Required

Optional

Optional

◎Welcome to discuss, please express your views here.

Hello, welcome to this website!

Label list

Links