SaguarragrandLong shaft submerged slurry pumpFeasibility analysis of application in condenser / qyxx_FJvien_6440

category：Machinery and industry equipment / date：2023-03-19 01:27:59 / browse：130 / comment：4

　　First, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs,　　 The reasons for excessive power loss are as follows: the running speed of the screw rod is too high.　　How to avoid this situation when the equipment is in use.Roosendaal　　Therefore, the stator winding will be burnt out due to excessive temperature rise.　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature,SaguarragrandFire deep well pump,SaguarragrandDrilling fluid slurry pump, the pressure drops to　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.

　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　 use a volt megger to check the insulation resistance, which should not be less than . megohm. If it is lower than this value, open the drain hole and vent hole for drying or drying.　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.Quality risk,　　We also need to limit the starting frequency and select appropriate thermal protection devices for use.　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also be

　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m,SaguarragrandVertical multistage centrifugal pipeline pump, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.High quality and low price,　　The of descending axial force can be used for slurry transportation in power plants, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　The specific treatment methods are as follows: first, check the power supply of the power supply to see whether the connector of the power supply is secure, whether the switch is tight, and whether the fuse is intact. In case of short circuit, short circuit fuse burnout and other problems, it shall be repaired in time. If it is not a power problem, check the water pump　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.Saguarragrand,　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance　　The whole packing body, including the packing gland, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane