category:Building materials / date:2023-01-31 05:37:02 / browse:144 / comment:3

As long as the pipe material is high-strength alloy steel

Classification introduction Small longitudinal crackJoint stock, including alloy steel pipes with temperature resistance, pressure resistance, wear resistance and low temperature resistance, the welding process shall be focused on preventing the tendency of martensite structure and cracks due to welding high-temperature operation. The general process requirements are that the welding rod shall be selected and baked as required and sent to the welder for use. The oil and water shall be removed before welding on both sides of the weld Rust and sundries shall be removed and cleaned. The welding line energy shall be as small as possible to minimize the swing during the welding process. The arrangement of the last weld shall have annealing effect on the heat affected zone as far as possible. Slow cooling after welding, cover with asbestos cloth, etc. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Yao, The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Introduction to product knowledge of alloy pipe:


Joint stock15CrMoG high pressure alloy pipeTeach you how to choose the right one for you



The section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.During the heating and cooling process of structural welded pipe workpiece, due to the inconsistent cooling speed and time of surface layer and core layer,Joint stockA335p11 American standard high pressure alloy pipe, the temperature difference will be formed, resulting in uneven volume expansion and contraction, resulting in stress, namely thermal stress. Under the action of thermal stress, the starting temperature of the surface layer is lower than that of the core layer, and the shrinkage is greater than that of the core layer, making the core layer stretch. At the end of cooling, the surface layer is compressed and the core is stretched because the cooling volume contraction of the core cannot be carried out freely. That is, under the action of thermal stress, the surface of the workpiece is compressed and the core is pulled.The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, rectangular section and slightly pure edge. Flat steel can be finished steel or it can be used as blank for welded pipe and thin slab for laminated thin plate.Inspection environment,The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, cold rolling by three high limited mandrel mill and cold rolling by fluctuating mandrel mill. In this way cold rolling by few station mandrel mill, the advantages of high efficiency, low metal material consumption, excellent product quality and excellent automatic control system are more and more widely used. The competitive advantage of the latter one is low cost and short whole process. It is suitable for the processing and manufacturing of CrMoG alloy pipes with large quantities, small types, multi specifications and high precision. Therefore, it is widely used


Joint stock15CrMoG high pressure alloy pipeTeach you how to choose the right one for you



Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.wholesaler,The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.The preparations for the construction of high-speed reinforcement mesh include the preparation and inspection of raw materials, the inspection and acceptance of the lower layer of the pavement, light I-beam has narrower legs, thinner waist and lighter weight than ordinary I-beam. No. - is large I-beam, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications,Joint stockCurrent price of 10 I-beams, dimensions and relevant standards.Joint stock,Patented manufacturing process of I-beam: I-beam has become a new industrial standard for wear-resistant materialsb. The professional two-sided arc welding processing technology can complete the electric welding at a good position,Joint stock48. How much is a ton of welded pipe, which is not easy to have the disadvantages of staggered joint, welding deviation and incomplete penetration, and it is very easy to manipulate the welding quality.Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main sleeves of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.

Copyright Notice: This article is not authorized by any Creative Commons agreement, you can freely reprint or use it in any form

 Articles that may be of interest

Comment area

share 3 Comments

user 984HP143755493 / 2023-01-31 07:16:29 / reply
It is very comfortable to do business with you. Responsible, serious, Joint stock15CrMoG high pressure alloy pipe is also good, I must give you a good comment. Looking forward to the next cooperation, I wish Rijin Doujin!
user 709HP180518493 / 2023-01-31 07:34:16 / reply
The first online purchase Joint stock15CrMoG high pressure alloy pipe. I use my personal experience to tell everyone that your service attitude is very good. The quality of the goods is also very good. I like you!
user 570HP155642700 / 2023-01-31 12:57:16 / reply
Can you give me a discount next time I buy it, Joint stock15CrMoG high pressure alloy pipe The quality is good, and I will live up to the boss

Comment / Cancel reply

Required

Optional

Optional

◎Welcome to discuss, please express your views here.

Hello, welcome to this website!

Label list

Links