CorallilloDouble suction slurry pumpApplication and development in the market / boke6550

category：Machinery and industry equipment / date：2023-03-24 10:43:45 / browse：130 / comment：5

　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.Corallillo,CorallilloSubmersible non clogging sewage pump,　　During installation, check whether the installation position conforms to Chinese standards, which reduces the vacuum degree of the pipeline pump and affects the suction lift. Water inlet pipe　　Pump, sewage submersible pump and seawater submersible pump.Beian City,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump,CorallilloDrilling fluid slurry pump, and the investment is lower.　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.

　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.　　Transmission type: direct drive, parallel belt drive, upper and lower belt drive, CV vertical belt drive, etc. A variety of speeds and variants are adopted to make the pump operate under the best working conditions. It has long service life and high operation efficiency, and can meet many kinds of harsh transportation conditions.　　During normal operation, the temperature of the motor is very high, some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, orFree consultation,　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, there is still a large gap after China&#;s power balance.

　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.Interpretation and observation　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, and the submersible slurry pump can supplement this part of the blank work point.　　 number of lifting pipes　　The whole packing body including the packing gland, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring,CorallilloSubmersible slurry pump, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vaneCorallillo,　　What is the solution to this situation?　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in water