category:Building materials / date:2024-04-12 02:47:34 / browse:52 / comment:5
Hardness QB square hardness is a pointer to measure the hardness and softness of metal materials. At present the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.QB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.Neville,In short,Neville22 galvanized square tube, the square tube production process includes these processes: tube blank & mdash& mdash; Cut off & mdash& mdash; Heating & mdash& mdash; Perforation & mdash& mdash; Pipe rolling & mdash& mdash; Sizing (reducing) & mdash& mdash; Straightening & mdash& mdash; Cut head and tail & mdash& mdash; Inspection & mdash& mdash; Packaging & mdash& mdash; Warehousing.Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.Mariel,If there is only a single plane weld, the step-by-step back welding shall be adopted from the middle, that is, the arc of the section weld shall be terminated at the section arc.Comprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C); (d) Q( B); (e) Q.Welding seamless welding seamless is to make welded elbows. After grinding and pickling, there is no sign of welding on the surface. Even using advanced flaw detection equipment, it can not be seen that they are welded elbows.
Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )The cutting surface of the square tube shall be true circle, and the cutting line shall be at right angles to the axis of the square tube. Excessive force is the reason for cutting the square tube into flat or oval, so the square tube should be cut with appropriate force.Ferrous metals refer to iron and iron alloys. Such as steel, cast iron ferroalloy, collectively referred to as iron carbon alloy.equipment maintenance ,Square tube has a wide range of application fields. Its main field is the construction industry, which promotes the development of economic construction. Because the production process of square tube hole is different the production design of square tube hole is also different. Next, I will introduce in detail the types of tube hole design below.According to metallographic classification,NevilleGalvanized pipe fittings manufacturer, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Square tube has a wide range of application fields. Its main field is the construction industry, which promotes the development of economic construction. Because the production process of square tube hole is different, the production design of square tube hole is also different. Next, I will introduce in detail the types of tube hole design below.
B. spring steel C. bearing steel tool steel: A. carbon tool steel; b. Alloy tool steel; c. High speed tool steel.average method,The technology of floating mandrel and square tube is gradually mature.Pile pipe and bridge; Pipes for wharf, road, building structure, etc. It is mainly used as petroleum geological drilling pipe, cracking pipe for petrochemical industry, boiler pipe, bearing pipe, high-precision structural pipe for automobile, etc.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.Neville,NevilleNational standard galvanized square pipe,C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.Square tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.
share 5 Comments
Comment / Cancel reply