EdmontonGalvanized pipe factoryAttention shall be paid to the following problems during construction / boke1017

category：Building materials / date：2022-04-21 10:32:05 / browse：342 / comment：4

Cold drawn or cold rolled precision square tube (gb-) is a cold drawn or cold rolled precision square tube with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision square mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality.Because the green billet can be pressed into any shape, it is easy to weld the square tube into difficult products.Edmonton,The general delivery length of square pipe is mm-mm, mostly mm and mm. The square tube is allowed to deliver short and non fixed length products not less than mm, or in the form of interface tube,Edmonton80 price of galvanized square pipe,EdmontonQuotation for galvanized square pipe, but the Demander shall cut off the interface tube when using it. The allowable deviation of the wall thickness of square pipe shall not exceed plus or minus % of the nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of the wall thickness when the wall thickness is greater than mm, except for the wall thickness of corners and weld areas. The weight of short gauge and non fixed gauge products shall not exceed % of the total delivery. For square tubes with a theoretical weight greater than kgm, it shall not exceed % of the total delivery. We have many different ways in square tubes. Different ways make square tubes have different characteristics. According to these characteristics, we can correctly select the appropriate application field, In this way the use efficiency of square tube can be improved. Next, we will mainly explain the characteristics of pipe cooling technology below. What are the main characteristics of square tubes? Square tube parts have accurate dimensions and smooth surfaces: the dimensional accuracy of cold parts developed at present can reach grade ~ . If ideal ones are adopted, their accuracy is second only to that of fine polished surfaces. Therefore, cold parts generally do not need to be reprocessed, and a small amount only need finishing (grinding).Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.Edinet, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.The other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, you can directly use the deformation angle & theta; Pass design.C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.

Stage ( & mdash; )Do a good job in the following aspects to effectively improve the service life of square tubesFor gas transmission: gas this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically due to the large amount of iterative calculation, steam and liquefied petroleum gas.Create brilliance,The technology of floating mandrel and square tube is gradually mature.Qb square tube, qb square tube,EdmontonGalvanized square pipe 140, qb square tube, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, but their uses are very different. The shape is different. Qb square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.We all know very well. Therefore, the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.

After spraying (throwing) derusting, it can not only expand the physical adsorption on the pipe surface, but also enhance the mechanical adhesion between the layer and the pipe surface. Therefore, spray (throwing) derusting is an ideal derusting method for pipelines. Generally speaking, shot blasting (sand) is mainly used for the inner surface treatment of the pipe, and shot blasting (sand) is mainly used for the outer surface treatment of the pipe. Several problems should be paid attention to in derusting by spraying (throwing).Quality improvement,Square tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry, but also can be seen everywhere in our daily life. The service life of square tubes is mainly affected by surface treatment. I will explain the specific operations of surface treatment of square tubes.For seamless qb square tubes, there is a certain hardness, so there are still many for bearing in application, so it is necessary to test the mechanical properties of seamless qb square tubes.For gas transmission: gas, steam and liquefied petroleum gas.Edmonton,Compared with other welding, mainly because of the exothermic reaction the material only needs to be heated below the melting pointFor oil, the oil brush work shall be carried out in accordance with the requirements of the rule system, so as to ensure the oil brush and the oil in the correct position of the brush and avoid wrinkles.The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.