category：Building materials / date：2023-01-27 00:48:53 / browse：109 / comment：5
. It is our responsibility not to pay attention to the maintenance of the pipe during transportation, mix the pipe with corroded chemical commodities, or soak the two water into the packaging film during transportation in rainy days, which will cause rust. . It is the responsibility of the processor and manufacturer. When cutting stainless steel or iron when manufacturing goods, the scrap iron will cause rust on the surface of the steel pipe. Therefore,Chiquimula304 spring stainless steel plate, it is only reasonable for highly skilled technicians to deepen investigation and discussion, and who should be responsible for whose achievements. You can't let steel mills, pipe factories, or users bear the liability for compensation!According to the purpose, it can be divided into oil well pipe (casing, oil pipe and drill pipe), pipeline pipe, boiler pipe, mechanical structure pipe, hydraulic prop pipe, gas cylinder pipe, geological pipe, chemical pipe (high-pressure chemical fertilizer pipe, petroleum cracking pipe) and marine pipe.Chiquimula, tensile strength, elongation and hardness of various stainless steel coils meet the requirements, the stainless steel coils must undergo heat treatment such as annealing, solution treatment and aging treatment before delivery. The corrosion resistance of stainless steel coil mainly depends on its alloy composition (chromium, nickel, titanium, silicon, aluminum, etc.) and the internal structure of stainless steel coil,. Raw material problem of stainless steel pipe. If the hardness is too low, it is not easy to polish (BQ is not good). If the hardness is too low, orange peel is easy to appear on the surface during deep drawing, which affects BQ performance. BQ with high hardness is relatively good.Ise-Ekiti,When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding,Chiquimula310 stainless steel belt price, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.When installing and welding the fixed port of stainless steel pipe, it is difficult to vent on the inner side, and some sides are easy to be blocked. In this case, water-soluble paper + blocking plate can be used for blocking. That is, the easy to vent and good side can be blocked with blocking plate, the difficult to vent and bad blocking plate side can be blocked with water-soluble paper, and the weld on the outer side can be blocked with adhesive tape (see Table ) .Hardness test: annealed stainless steel pipes with inner diameter of more than mm and wall thickness of less than mm can be tested by w-b Vickers hardness tester, which is very fast and simple, and is suitable for rapid and nondestructive qualification test of stainless steel pipes. For stainless steel pipes with inner diameter of more than mm and wall thickness of more than mm, Rockwell hardness tester shall be used to test HRC hardness. Stainless steel pipes For stainless steel pipes with inner diameter greater than mm and wall thickness less than mm, the surface Rockwell hardness tester shall be used to test HRT or hrn hardness. For stainless steel pipes with inner diameter less than mm and greater than mm, the special Rockwell hardness tester for pipes shall be used to test hrt hardness. When the inner diameter of stainless steel pipes is greater than mm, the Rockwell or surface Rockwell hardness tester can also be used to test the hardness of pipes.
Some reasons for product composition ratio: in order to reduce the production cost, reduce the proportion content of some important elements such as chromium and nickel, and increase the content of other elements such as carbon. This production phenomenon that the composition ratio is not strictly in accordance with the product model and product characteristics not only greatly reduces the product quality, for example, when the chromium content of stainless steel pipe is insufficient, it not only affects the production The corrosion resistance and formability of products have potential product quality and safety hazards when they are used in chemical, equipment and production industries. At the same time, they also affect the appearance and oxidation resistance of products.D-outer diameter (mm) as stainless steel pipe for reprocessing device, in order to reduce carbon content by vigorously welding chromium carbon compounds at affected parts, in order to improve the corrosion resistance of ULC steel, the steel industry with phosphorus content below .% is manufactured. After times of % boiling corrosion test it is found that if the corrosion degree of the solution treated material is less than .mm/a, ℃ & times; The sensitized material for h has excellent corrosivity when the corrosion degree is less than .mm/a.There is a bright future for domestic substitution for imported stainless steel pipes. Since the s, China has solved the problem of reducing wall thickness and cost; High diameter to wall ratio and high precision & rdquo; The technical problems of stainless steel pipe make the stainless steel pipe applied and developed rapidly. If a pipeline can be fully applied, localization is indispensable. At present some domestic have the ability to produce and further develop stainless steel pipes and fittings.device management, the following key points should be paid attention to: during the welding processWhen using this process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, no concave,ChiquimulaStainless steel tape magnetic, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.;- Ferromagnetism due to m transformation shall be considered in use (such as in instrument parts).The intergranular corrosion of austenitic stainless steel can be prevented by adding Ti, Nb and other elements that can form stable carbides (tic or NBC) and avoiding the precipitation of crc on the grain boundary.
Using CrO and hsoho as the main components and adding an appropriate amount of mnso.ho coloring solution, the chemical coloring of stainless steel industrial pipe was carried out. The effects of pretreatment process, coloring solution temperature, mass concentration and coloring time on the color film of stainless steel industrial pipe were discussed. Through a large number of experiments, a good formula and process range of coloring solution are obtained. With the increase of temperature and time, the film thickness increases, and the color changes are brown, blue gold, purplish red and green. After curing and sealing treatment, good reproducibility, and significantly improved wear resistance and corrosion resistance.Honest management,The continuous casting of stainless steel pipe fittings is generally matched with the refining furnace, which has strict requirements on the chemical composition and temperature of molten steel; In order to prevent secondary oxidation of molten steel, non oxidation protection pouring is required during continuous casting production; Strict requirements for refractory materials such as ladle, tundish, corner, working pressure and other factors.For example, the price of tons of goods = tons = the result example: the price excluding tax of ton of goods = a ton = ~ the total weight of the known coil weight and price = the coil weight price, the thickness of stainless steel plate & Chi; Width & Chi; Long & Chi; e.g. & Chi; Χ Χ = kg stainless steel plate weight per square meter (kg) calculation formula: specific gravity thickness (mm) width (mm) length (m) stainless steel weight per meter (kg) stainless steel pipe calculation formula: diameter (mm) diameter (mm) (correct calculation of the price difference between burr and trimming of nickel stainless steel . chromium stainless steel) in the market, the price difference between burr and trimming of stainless steel is usually set at a fixed price. For example, it is generally considered in the market that the price difference between burr and trimming of is yuan tons and that of is yuan tons. In fact, this method is not scientific. In fact, the price difference between burr and trimming of stainless steel is different The correct calculation should be like this.Chiquimula,Formula for hydraulic test pressure of stainless steel welded pipe for weight calculation fluid (gbt-): where: P - test pressure, MPa; R - stress, taking yield point of %, MPa; s - nominal wall thickness of steel pipe, mm; D - Nominal outer diameter of steel pipe mm.Production mode stainless steel pipe can be divided into seamless pipe and welded pipe according to the production mode. Seamless steel pipe can be divided into hot-rolled pipe, cold-rolled pipe, cold drawn pipe and pipe. Cold drawing and cold rolling are the secondary processing of steel pipe; Welded pipe is divided into straight seam welded pipe and spiral welded pipe.Application field: launch the market plan of stainless steel pipe in the target market of new products, such as stainless steel kitchen equipment.
share 5 Comments
Comment / Cancel reply