category：Environmental protection / date：2022-02-27 00:49:54 / browse：1168 / comment：4
SPC floor does not use strong glue in the production process, so there are no indoor formaldehyde, benzene and other harmful substances.The indoor formaldehyde emerald green floor is not easy to cause damage to the body. Main performance.Jacksonville, Remove the original open putty from the edge, seal the edge again, apply primer on the whole floor and wait for drying. In terms of foot feeling, solid wood is better than reinforcement. According to national industry standards, all solid wood is mm thick, and wood keel ceiling is selected for installation, so the upper foot is better than mm thick reinforcement plate.How to distinguish true and false solid wood flooring?Macenta,JacksonvilleSmooth floor leather,Narrow board specifications are also China&#;s characteristics. Solid wood flooring looks generous, too expensive and has poor stability; China&#;s flooring manufacturers make imitation solid wood flooring. Looking at its specifications as solid wood flooring, it is cheap and stable. The four sides are made into V-grooves, which can really confuse the fake with the real, and the thickness is basically about mm. It has been implemented in the market for less than a year and is very popular.thicknessStructure: solid wood surface material, basic manual.
Wooden wedges and nails shall not be used for fixing during construction.The contact surface between the wooden wedge and the nail is too small, and the grip strength of the nail is insufficient.Bones are easy to loosen, and people will make a sound when stepping on them.Fear of water and moisture: the base material of laminate floor is medium and high density board, with small relative density and large expansion coefficient. Once the reinforcing layer is filled with water after paving, if it is not wiped in time, it is easy to cause blistering and deformation due to water absorption and expansion. Its moisture resistance is not strong, and its stability is poor in humid environment.Solid wood flooring is not very good in terms of wear resistance, but in composite flooring, the wear resistance of solid wood composite flooring is also very different from that of reinforced composite flooring.With special components, the wear resistance of reinforced composite floor is much higher than that of ordinary solid wood floor.project, Defects. High cost performanceAt the same time, SPC fine floor is also a good choice.The price of this floor is reasonable but fashionable.The best choice.
Rich colors and patternstargetFourth, after-sales maintenance service.Generally, reliable flooring companies and well-known brand operators with overall strength have done very well in after-sales maintenance service.We all know the truth of three-point floor and seven point installation, so we must choose a professional installation teacher to install it.What kind of floor is good for bedroom design?Solid wood flooring Fire protection, fire rating B, second only to stoneJacksonville,： I can smell faint wood fragrance. This floor shows that the glue content is very low.Up to European standard E level.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing glue shall be applied on the ground according to the size of the floor paint cloth, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting,JacksonvilleHome floor leather, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, they can be wiped with alcohol.In this way, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Waterproof: apply waterproof resin or other waterproof materials at the tongue and groove of the laminate floor, so that the moisture and moisture outside the floor are not easy to invade and the formaldehyde inside is not easy to release,JacksonvilleLaminate price, so that the environmental protection and service life of the floor are significantly improved;Especially when laying in a large area, it is inconvenient to leave expansion joints and compression strips, it can prevent floor arching and reduce floor contraction joints.
share 4 Comments
Comment / Cancel reply