category：Building materials / date：2024-09-19 01:09:04 / browse：35 / comment：4
How to lay lacquer cloth?The construction procedures and methods are as follows: first, measure the structural size of the room accurately;Then cut the lacquer cloth according to the size.Note that the cutting width should be slightly larger than the required width to facilitate overlapping, matching and trimming during paving.The cut floor paint cloth shall be placed at room temperature of no less than ℃ for about hours, so that the crimped part of the floor paint cloth can be fully extended and ready for the final paving.Special adhesive shall be used for paving the floor paint cloth.Before paving, the indoor ground shall be treated first.Well known brands: LG and Hanhua flooring in Korea, Armstrong flooring in the United States, Jiefu and Tejia flooring in France, fulbo flooring in Sweden, longxilu, tahilong, Dongli flooring in Japan, and domestic bonier flooring.For the pursuit of cost performance, choose Korean brands, Japanese brands for the pursuit of quality, European and American brands for the pursuit of brand effect, and domestic brands for low prices.Polech, Use the humidity detector to detect the humidity and ensure that the dry humidity is reasonable.The flame retardant grade is B, and the formaldehyde concentration is acceptable.Precautions for solid wood floor installation : prevent uneven ground.Leixlip SPC floor surface will not have holes and water seepage;There will be no seams after splicing. After being stained, wipe it gently with a rag to clean it easily, leaving no marks that are difficult to remove, and there is no need to maintain it with special maintenance products.The combination of hardness and softness.The wood floor in the living room should be made of boards without knots, cracks and mildew. Generally, Fraxinus mandshurica, camphor and teak are better, because their lines are beautiful and clear, and their texture is moderate.The laying method of wooden floor is not very difficult, but it is required to have a certain carpentry foundation.Firstly, the wood board shall be processed into the length and width coordinated with the room size according to the room size and the floor shall be cleaned before laying.When laying, draw the center point and vertical and horizontal vertical lines of the room, and lay from the center to the four sides. glue and an appropriate amount of cement can be used for bonding between laths.Note that the glue must be coated evenly to avoid the warping of the plate.Melamine surface coating is generally used for wallboard tabletop board, etc. it is used in places with low wear resistance requirements. In the flooring industry, this kind of surface coated floor is called 'false floor'Its wear-resistant revolution is only - revolutions. If it is used with high strength, the decorative paper on the surface will wear out after two or three months. The standard laminate floor will not have such a problem after years of normal use. There is no wear-resistant layer on this kind of floor decorative paper,PolechIs floor leather flame retardant, the pattern is beautiful and clear, which is the place where laymen are easy to be fooled.
As mentioned above, calcium powder has good thermal conductivity, so paving the floor at home is the best choice. Even if it gets hot, it will not release harmful gases.SPC floor is a new type of floor also known as stone plastic floor. Its base material is a composite plate made of stone powder and thermoplastic polymer, which is stirred evenly and extruded at high temperature. At the same time, it has the characteristics of wood and plastic to ensure the strength and toughness of the floor.SPC floor does not use strong glue in the production process, so there are no indoor formaldehyde, benzene and other harmful substances.The indoor formaldehyde emerald green floor is not easy to cause damage to the body.Then look at the qualityIndustry management Scrape the board with a blade. There are standard, wide plate and narrow plate in terms of specificationsThe first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.
Test: for the ground lacquer cloth with thin thickness, you can tear it by hand. If it can be easily torn off, the tear strength of such ground lacquer cloth can not meet the requirements. After gently rolling up and pressing down, if it can not be restored to the original state and leave an indentation, such a product has poor softness.If the layers can be torn by hand, it indicates that the product layers are not well combined, and stratification will soon occur in future use.Plastic floor paint cloth has the advantages of light weight, elasticity, good mechanical strength, good foot feeling strength, comfortable foot feeling, wear resistance, pollution resistance, corrosion resistance, heat insulation, sound insulation, moisture resistance, small water absorption, good insulation, easy cleaning, simple construction, convenient maintenance and low price. In a large number of civil buildings and public places, it has high requirements for cleanlinessIt is widely used in the laboratory.Plastic floor paint cloth belongs to soft floor. It is a floor coil produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.The length of each roll of plastic floor paint cloth is m ~ m, the width is mm ~ mm ~ mm and the total thickness is mm (machine room) ~ mm (plant and public buildings)For long-term indoor use, high and medium grade products should be selected, and products produced by well-known brands and regular enterprises should be purchased as far as possible. Such products have sufficient thickness and good interlayer adhesion, and are not easy to layer and curl, especially foamed leather, which gives people a comfortable and elegant feeling. If you want to use them for a short time or one-time cover, you can choose low-grade products because low-grade productsThe price is low and there are many prices to choose from, but many of these products are processed with waste materials, with poor flexibility, generally thin thickness and large shrinkage coefficient. When checking the appearance quality of rubber plastic floor paint cloth, it should be under scattered sunlight or fluorescent lamp, and the illumination should be ( ± LX, LM from the tested sample, conduct oblique visual inspection. First, observe whether there are cracks, fractures and delaminations on the surface of the local lacquer cloth. If there are, it can be judged that the local lacquer cloth is unqualified. The second step is to observe whether there are wrinkle marks, bubble pollution points and pattern deformation. Those that cannot be observed are excellent products and first-class products; those that are slight but not obvious are recognized as qualified. Go back to the third step for observationIf there is any missing pattern on the surface of the ground lacquer cloth, or if there is any defect of the transparent wear-resistant film on the surface, it is the first-class product and the first-class product. If there is a slight missing print or lack of film, it is the qualified product, otherwise it is the unqualified product. Finally, carefully check whether there is deviation in the multi-color overprint on the surface, whether there is color difference in different parts, if the top-class product is uneven, if there are the above two defects, it is the first-class productProducts that obviously have the above defects but do not affect the overall beauty are judged as qualified products. Finally, the appearance quality of ground lacquer cloth is determined based on the above judgment. When selecting ground lacquer cloth, first smell whether it has pungent smell. There will be a slight smell after the good coil is opened, and the smell of inferior products is stronger; secondly,PolechWood floor damp proof pad, calculate the use area, and the same room should be selectedCoiled materials with the same batch number, pattern and thickness. When purchasing, carefully observe the appearance quality open a roll of ground lacquer cloth, separate the ends for a few meters, observe the surface layer of the sample, the surface layer is thick, the wear-resistant layer is thick, and the service time is long, and then observe whether there are cracks, fractures, wrinkles, missing, lack of film and overprint deviationDefects such as color difference, color difference and pollution.Quality inspection report,The most common causes of wood floor cracking are the moisture content of the floor and the dry humidity of the environment. For example, the moisture content of the wood floor is % and the local average moisture content is %. In order to balance the moisture content of the floor and the moisture content in the air, the dry air absorbs moisture from the wood floor, and the wood floor cracks in this process After the primer is dry, brush the first finishing coat and dry it. SPC floors are subject to biological resistance treatment, and the unique sealing of the surface layer makes the products have the characteristics of anti bacteria and antibacterial, and meet the cleaning requirements of various departments and institutions.When it comes to the choice of decoration flooring, you can think of ceramic tile, marble and wood flooring. However, SPC flooring has become the first choice for people to buy Flooring in developed countries and regions such as Europe, America, Japan and South Korea,PolechMultilayer solid wood floor, and the domestic market is gradually accepting SPC flooring. Why SPC flooring is popular? First of all,Now let&#;s learn what SPC floor is and how SPC floor is.SPC is the abbreviation of stone plastic composites (stone plastic composites). The main raw material is polyvinyl chloride resin. It is made by extruding SPC substrate by extruder combined with T-shaped die, laminating and embossing PVC wear-resistant layer, PVC color film and SPC substrate by three roll or four roll calender at one time. Glue is not used in the production process.Polech, After days, the nano fiber feels more astringent when it is exposed to water and is less likely to slip. The more it meets water, the more astringent it becomes.It is suitable for families with old people and children. It is the preferred ground material in public places with high public safety requirements, such as airports, hospitals, kindergartens, schools, etc. Solid wood flooring.
share 4 Comments
Comment / Cancel reply