category：Machinery and industry equipment / date：2024-04-23 01:21:22 / browse：36 / comment：5
The lifting stage can provide real-time information on the operation of the entire vehicle, avoiding relying solely on the experience of operators to coordinate with each other, and improving the reliability and safety of the system. The definition of safety zone is very important because the lifting stage has a large range of movements, and it must be accurately calculated. The lifting stage has two structurally separate systems, the ground turntable and the high-altitude work bar. However, for various movements on the vehicle, it is also an interconnected system, which needs to consider the priority of operation, system redundancy, and safety assurance of actions.The surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %.Pila, and then ring the bell to start. It is strictly prohibited to work with the movable doors of the protective fence open. In case of special circumstances during platform operation the emergency stop switch can be used to stop the platform. However, it is prohibited to use the emergency stop switch to stop the platform.All connecting shafts must have split pins and be sufficient.Jawf al Maqbabah during normal operation, gearbox, external meshing gear and other parts, as well as the hydraulic oil, especially in the cold sun or rainstorm climate, the reaction speed will be accelerated, so the exterior paint on the warehouse goods elevator will show signs of aging and then fall off every once in a while. Therefore, when maintaining the equipment of the lift table at ordinary times, pay attention to its storage, let alone in cool days or rainstorm
?? The supervision unit shall effectively fulfill its safety responsibilities, and if any potential production safety accidents are found, it shall require the installation unit and the user unit to rectify within a specified period of time. If the installation unit and the user unit refuse to rectify, they shall promptly report to the construction unitWhen the lifting base plate descends,PilaMobile scissor type lifting platform, the safety net below immediately stops running and descends when encountering obstacles.The wear rate is fast, and due to factors such as processing, assembly and adjustment of new machine components, the friction surface is rough, the mating surface area is small, and the surface pressure condition is uneven. During the operation of the machine, the concave and convex parts on the surface of the parts are intertwined and rubbed against each other. The metal debris that falls off from the grinding process, in turn, acts as abrasive and continues to participate in friction, further accelerating the wear of the mating surface of the parts. Therefore, during the running-in period,PilaMobile lifting platform scissor fork type, it is easy to cause wear on components (especially the mating surface), with a fast wear rate. At this point, if overloaded, it may cause damage to the components and lead to early failures.Work courses,Check the smooth steel wire rope and various fasteners, if there is excessive wear, it is necessary to replace themCheck the wear condition of the pinion and rack, please refer to the instruction manual for specific requirementsCheck if the orientation of the upper and lower limit blocks on the guide rail frame is correct
Check the oil level of the gearbox and make up for new oil if necessaryWhere can I find it?,Check the clearance of the ball bearing and the wear of the suspension wheel guide wheel. If the roller is worn, it is necessary to adjust or replace it. If the elevator bearing is worn, replace the guide wheel or bearingThe second method is the protective layer method, which covers the metal surface of the aluminum alloy lifting platform with a protective layer to isolate the metal products from the surrounding corrosive medium and prevent corrosion. Apply engine oil, petroleum jelly, paint, or cover the surface of steel parts with corrosion-resistant non-metallic materials such as enamel and plastic; It is not easy to apply a layer of electroplating, hot plating, spray plating, etc. on the surface of steelCheck the smooth steel wire rope and various fasteners,Pila12 meter aluminum alloy lifting platform, if there is excessive wear, it is necessary to replace themPila,Lifting and loweringOrganize, remove rust and repaint the structural components such as the suspension cage and guide rail frame for corrosion and reinforce the severely corroded load-bearing membersHow to maintain and maintain the stage? When using the lifting stage in daily life, attention should be paid to maintenance to extend its lifespan. Below, Jinan Dasheng Hydraulic Machinery will introduce several maintenance and attention points for everyone: the brakes of each mechanism should be regularly inspected and adjusted for the clearance between the brake pads and wheels to ensure flexibility and reliability. On the friction surface, there should be no dirt present, and any dirt must be washed off with gasoline or thinner. Pay attention to checking each steel wire rope for broken wires and loose strands. If it exceeds the relevant regulations, it must be replaced immediately. Professional elevator manufacturers have a complete range of products, which are popular both domestically and internationally. Our equipment has a long service life! The industry leader in product wire products, welcome to inquire
share 5 Comments
Comment / Cancel reply