Alot NangoCold storage construction designWhat are the uses and features / 6892-subject

category：energy / date：2023-05-01 00:07:05 / browse：156 / comment：5

The spacing of pull rivets at inner and outer corners is mm and mm respectively; After the polystyrene library is installed, the wall panel joints shall be evenly sealed and decorated with silicone sealant.For the flushing (thawing) drainage pipe in the cold room with different temperature, an exhaust valve equipment shall be set before connecting the flushing (thawing) drainage pipe.Alot Nango,Air tightness test: air tightness test of fresh storage system, also known as leak detection process, which can be divided into pressure, vacuum and ammonia filling leak detection stages.The water tank is designed to be separated from the machine body and is double-layer. It will not drip due to condensation caused by internal and external temperature difference. It can be interlocked with the refrigeration system, that is it will not be humidified during refrigeration to prevent serious frosting of the fan.Gemena,The installation of cold storage board is a link of the cold storage installation project. High price cold storage installation of various specifications, cold storage installation, cold storage construction, fruit preservation cold storage, medical cold storage. Waste merchants, industry enterprises and power departments are welcome to visit and negotiate! The cold storage body and storage plate include: floor, vertical plate and ceiling plate. The installation of storage plates in different directions and precautions are as follows: enter the construction site, verify the construction situation according to the construction drawings, determine the equipment installation position, and then refer to the following specifications.Connect the refrigeration system. Wires and copper pipes shall be used to connect the refrigeration unit, electric control system and other components of the cold storage. The connecting pipes shall be closely connected, and corresponding thermal insulation and protection measures shall be taken.For water-cooled units, the turbidity of cooling water shall be frequently, the cooling water shall be replaced frequently, and whether the running, emitting, dripping, leakage and other conditions of the water supply system exist.

Anti odor floor drain shall be set on the pavement of refrigeration room and refrigeration unit room, electronic pit and other places convenient for drainage shall be provided with drainage and equipment to avoid backflow of water.The selection of the refrigeration system of the controlled atmosphere storage is mainly the selection of compressor and evaporator. The refrigeration system is the core of the controlled atmosphere storage, which is mainly composed of compression system, evaporation system and regulating valve. In addition,Alot NangoMedicine frozen warehouse, duct and instrument. The whole refrigeration system is a sealed circulating circuit in which the refrigerant circulates, The compressor is the heart of the refrigeration system, which promotes the circulation of refrigerant in the system. The function of the condenser is to remove the heat from the compressed gaseous refrigerant and condense it into liquid refrigerant; The cooling methods of the condenser include air cooling, water cooling and the combination of air and water. Air cooling is only used in the refrigeration equipment of small-scale air-conditioned storage. The role of the evaporator is to provide cooling capacity to the air-conditioned storage. The evaporator is installed in the air-conditioned storage. The blower blows the cooled air to all parts of the storage. The air duct of large-scale air-conditioned storage is commonly connected with the evaporator to extend the air supply distance, Make the storage temperature drop and even.Preparation, prepare the project planning of cold storage, and prepare the construction site and construction materials. All kinds of materials for cold storage construction are customized according to the needs of customers. Sort out the construction site that meets the requirements, transport all installation materials to the construction site, check the material quality and model, and start the installation of cold storage after confirmation.install,The exhaust temperature of the compressor equipment is often. When the season changes and the temperature difference changes greatly, pay attention to it. If the machine is abnormal, it needs to be checked in time.Pay attention to the energy saving of the lighting system: the lighting of the cold storage should be considered comprehensively according to the area, height and warehouse temperature of the cold storage on the basis of safety, science and rationality, from the perspective of energy saving and environmental protection. The lighting in the cold storage is concentrated in the working area.The product shade warehouse is a warehouse location below ℃ and the sun cannot be straight. The humidity is % ~ % relative humidity, and there are corresponding strict requirements for the wall, ceiling, ventilation disinfection and epidemic prevention of the warehouse. The refrigeration system adopts full-automatic microcomputer electrical technology and does not need to be on duty. It mainly stores western and Chinese grass materials and instruments, and can monitor and record the temperature and humidity in the storage area.

Cold storage has good fire and flame resistance. After adding flame retardant, polyurethane is a kind of flame retardant and self extinguishing material. If it is burned by fire, it can be carbonized, unlike flow burning and flashover like extruded board, which can effectively prevent fire spread. In particular it can be closed as a whole after fire prevention treatment to form non combustible products.Credit guarantee,The physical properties of polyurethane insulation board are relatively good,Alot NangoInstallation of small cold storage equipment, which can meet different needs. The polyurethane insulation board is also strict in the selection of materials. It is a special product manufacturing enterprise integrating R & D, and service. It has long been specialized in cold storage installation,Alot NangoCold storage installation and maintenance Telephone, cold storage installation, cold storage construction, fruit preservation cold storage and medical cold storage. It improves the overall performance of the polyurethane insulation board and enables the polyurethane insulation board to work for a long time, Polyurethane insulation board has also become one of the main exterior wall materials.The shelves in the warehouse shall have sufficient strength and rigidity.Cold storage construction: which one is suitable for you? Which one is suitable for you?Alot Nango,Simple refrigeration is based on the volatilization of refrigerant in the condenser of the cold storage, so as to cool the refrigerant, and then input the refrigerant into the box or building of the refrigeration equipment to cool the air according to the heat exchanger. This kind of refrigeration has slow cooling speed, large total heat conduction temperature difference and complex system software, so it can only be used in less places, such as brine ice making and cold storage with constant temperature requirements.Thermal insulation performance of thermal insulation materials for food cold storage the requirement of polyurethane thermal insulation materials for cold storage is thermal insulation performance, and the quality of thermal insulation performance cannot be observed before it is really put into use. It is too late to observe the difference between power consumption. In this large number of experimental tests, and its heat preservation performance is obviously better than that of ordinary foam with thick wall and big hole. The use of the tasteless amine catalyst can effectively adjust the balance between foaming and gel reaction, so that the interlayer skin of the sprayed coating is thinner, which is beneficial to the performance of the thermal insulation material of the cold storage. Ordinary polyester polyols are not used.The importance of regular oil discharge, descaling and air discharge in the refrigeration system of the warehouse.