Bird droppingsSplit vertical pipeline pumpDuctility of / 6539content

category：Machinery and industry equipment / date：2023-03-24 00:16:45 / browse：121 / comment：5

　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local placesBird droppings,　　 tailings transportation,Bird droppingsSmall deep well pump, various tailings ore, pulp, coal slurry, slag, slag treatment, etc.　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.Goma,　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.

　　 When stopping the operation of the submersible slurry pump close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline,Bird droppingsSubmersible non clogging slurry pump, and After that,Bird droppingsCarbon steel explosion-proof pipeline pump, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　 Determine the head h. After the flow is determined, determine the inlet and outlet pipe diameters of the pump, complete the layout of the whole pipeline, and determine the head. In the actual selection, the resistance coefficient of the pipeline is often too large. In addition when selecting the pump model, a head margin is added, resulting in　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.Highly recommended,　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, such as the submersible pump for domestic water and farmland irrigation and pumping　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should choose　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump

　　 Then reinstall the equipment on the engine and install the rubber hose.Variable cost, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve　　Environmental conditions for normal operation of ordinary YLB motor:　　Then it can enter into the volute pump housing. Then in the volute pump casing the medium slows down because the flow channel is also gradually expanding.Bird droppings,　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps may　　Rate.