category：Machinery and industry equipment / date：2023-03-19 00:42:44 / browse：126 / comment：4
Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point. There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications, if its model is not correctly and reasonably selected,BeukarSplit vertical pipeline pump, its application effect will be greatBeukar, To help you solve the problem of removing the impeller of the slurry pump, we only need to fix the pump shaft and rotate the impeller in reverse to remove the impeller easily. For large pumps with impeller removal ring, we need to remove the impeller removal ring first, and then rotate the impeller. Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.Esposende, It will burn out. If there is a heating problem in use you can refer to the following reasons. After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and The pump should be divided into two aspects: electricity and machinery. As for machinery, you can compare the previous maintenance records. The second is electricity. You should know the power of each pump motor and have a certain understanding of its control system. Slurry pump with mechanical seal
The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing The long shaft deep well pump is equipped with two types of motors: ordinary vertical Y series motor (equipped with PTS thrust disc) and hollow shaft YLB series motor for deep well pump. The insulation grade is divided into class B and class F. now, with the progress of science and technology and the continuous development of products, YLB series has developed high-voltage, protection and other grades up to When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the waterSafety production, Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, it is also possible that the temperature is too high due to the low voltage of the water pump.
Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition, for submersible slurry pumpQuality improvement, for screws that are too tight or rusted for a long time the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places. (d) The average maximum relative humidity in the wettest month is %. At the same time, the monthly average minimum temperature is not higher than ℃ add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, it means that the pump is fullBeukar,BeukarWQ submersible sewage pump, The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump,BeukarVertical slurry pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time. If there are sundries blocked the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time
share 4 Comments
Comment / Cancel reply