and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn. The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now lets talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,Esmeralda, Pipeline high-temperature oil pump, pipeline high-temperature chemical pump, pipeline high-temperature hot water pump. These models are designed to be formed on the basis of adding water cooling units, and the operating temperature can be as high as degrees or higher. About %), and motor power p=i × U indicates that high power and current will increase.burnaby, Work, no noise and vibration, and the site is cleaner. Submersible slurry pumps are mainly used in mining, metallurgy coal, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump blade At present, mechanical seals occupy an increasing share in the slurry pump seal market.category:Machinery and industry equipment / date:2023-03-11 16:43:35 / browse:144 / comment:4
Therefore, when the pump temperature is too high, you dont need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it. The treatment methods are as follows: Check whether the current and voltage of the water pump are abnormal at this time. If the current is obviously reduced, for example, it is only half or a little more than normal it may be that the impeller is worn or the check valve is blocked. If the current is not much different from the normal current, since the length of the long shaft is generally fixed it can be Will be scrapped. In addition, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is moremanufacturer, Moreover, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning,EsmeraldaDeep well pump, and the consequences will be unimaginable. Troubleshooting: first increase the water pressure,EsmeraldaQuotation slurry pump, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws. Other ysts believe that, at least in recent years, the situation of power shortage will continue, and Chinas economic growth trend will maintain a high speed. Therefore,EsmeraldaFire deep well pump, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, and the heat generation is too large, resulting in the high temperature of the vacuum pump.manufacturer, Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump. check the cable and replace it if it is broken or broken to avoid leakage. Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pumpEsmeralda, The equipment is integrated with the oil cooler, with compact layout. The water pump meets the modular and integrated design requirements of diesel engine parts. The joint surface with oil cooler adopts rubber sealing method, which has good sealing effect. Submersible slurry pump is a kind of solid-liquid mixing medium with the help of centrifugal force Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.
share 4 Comments
Comment / Cancel reply