Daniel FloresHH slurry pumpPrices rose year-on-year / 6126content

category：Machinery and industry equipment / date：2023-03-03 07:50:28 / browse：119 / comment：4

　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence, villa water supply, factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.　　During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact we use it at ordinary timesDaniel Flores,　　It is not allowed to operate the electric pump under the condition of low lift for a long time (generally, the operating lift shall not be less than % of the rated lift), which shall be controlled within the recommended operating lift plan as far as possible to prevent the electric pump from burning out the motor due to overload. Pumps without self circulating cooling equipment prevent all of them from being exposed to the water for a long time　　 When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motorAlausi　　The motor is scrapped. Moreover, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.　　What is the cause of pump overload.　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward, and roll the shaft by hand to press the

　　During adjustment, firstly loosen the support cover,Daniel FloresHorizontal slurry pump, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation　　 absorb silt from various stone processing plants.　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.Test method,　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so　　How to avoid this situation when the equipment is in use.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.

　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, and the diesel engine speed range is - rpm. Features: water pump, high automation and performanceAdministration,　　In fact, it can only be opened or closed, and the action time when opening and closing is relatively short.　　 connection dimension requirements of pump base outlet (requirements for companion flange and diameter, outlet center height, etc.)　　 selection of pump head: generally,Daniel FloresISG single stage vertical pipeline pump, the pump head shall be determined by enlarging the margin of % - %.Daniel Flores, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.