category：Building materials / date：2023-01-28 14:36:59 / browse：92 / comment：6
I-beamI-beam is a kind of economical section steel with better section mechanical properties. Its characteristics are as follows:San Jose pinuraClassification by wall thicknessDue to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Pradera,Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.→ wide flange and large lateral stiffness. Strong bending resistance.→ I-beam can be processed into T-beam, and honeycomb beam can be combined to form various section forms, which greatly meets the needs of engineering design and manufacturing.
Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.From the situation of chiseling on site, the reinforcement mesh laid by the construction party is cm below the surface layer, which greatly exceeds the specification, and then the crack resistance of the reinforcement mesh can be reduced. Because of the increasing temperature, the effect of thermal expansion and cold shrinkage and the characteristics of concrete, the cracking of surface layer is significant.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.Customer firstThe core of C-section steel is the structural system of braced frame. More than half of such senior managers in China are the former. Unfavorable to earthquake resistance. Hydraulic power, and the power is large, generally about KW, which is similar to the plate shearing and bending machine. The general control process is complex, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.a. In the forming process, the thick steel plate has uniform deformation, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size, specification and model of diameter and wall thickness, especially in the production and manufacturing of steel structure design grade thick wall pipe, especially medium diameter small thick wall pipe, which has incomparable advantages of other processing technologies,Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is,San Jose pinuraDN50 seamless pipe price, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.The production of plastic impregnated welded steel wire mesh is to immerse the formed welded steel wire mesh into a stone groove filled with PVC powder. The dry forming process is complex and the cost is much higher than that of spray welded mesh. Due to different application ranges and different uses, which needs to be determined according to its actual use.What should we pay attention to in the production of alloy pipeSan Jose pinura,The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Classification introduction Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, that is, the combination of more than two systems. For example straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole, etc.