Los PalaciosIrrigation deep well pumpWhat are the crystal structures of / 49baec_466HP159575805_6172

category：Machinery and industry equipment / date：2023-03-05 16:48:31 / browse：133 / comment：4

　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial,Los PalaciosSplit vertical pipeline pump, so the motor must be waterproof and sealed,　　There is a blockage in the water pump.　　For example, in the market, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.Rio Negro,　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　We also need to limit the starting frequency and select appropriate thermal protection devices for use.　　 First remove the pump from the engine.

　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　The motor burns out the winding due to heat dissipation. The water pump shall be lifted and lowered at any time with the change of water level in the well. In case of water reduction or interruption, the cause shall be found out immediately or the pump shall be shut down for inspection. The cable shall not rub against the shaft wall to prevent the well water from penetrating into the motor along the cable core after the cable is worn.　　All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.Application process,　　During normal operation,Los PalaciosSubmersible sewage pump, the temperature of the motor is very high some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use

　　At the same time, the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.management,　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!　　How to avoid: the impeller body and shaft are connected with keys, and the end is locked with impeller nuts. Because the outer diameter of the impeller nut is small, the torque during reflux is small, and the impeller nut is close to the circular shape, so it can well prevent reverse loosening caused by reflux. Of course, there are many details　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.Los Palacios,Los PalaciosSubmersible non clogging slurry pump,　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local places　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.