category：Building materials / date：2022-05-28 01:08:10 / browse：394 / comment：3
The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.The reason why the surface of fake and shoddy materials is easy to crack is that its blank is adobe with many air holes. During the cooling process, the adobe has cracks due to the action of thermal stress, and there are cracks after rolling.Kingston,Before gas cutting, remove the dirt and grease on the steel surface, and leave a certain space below to facilitate the blowing out of slag. During gas cutting, the movement of the cutting torch shall be kept at a uniform speed. The cutting surface should be ~ mm away from the tip of the flame core. If the distance is too close, and if it is too far away the cutting will be interrupted easily due to insufficient heat.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.Belford Roxo,Square tube, modified square tube, QB square tube and hot-rolled square tube are qualified in quality inspection. The manufacturer adopts advanced equipment to ensure the quality of each product. Magnetic flux leakage testing for surface defects of square tubes is very similar to magnetic particle testing for square tubes, and its scope of application, sensitivity and reliability are stronger than magnetic particle testing. Indirect square forming process the traditional forming process of cold-formed square pipe is to gradually roll the hot-rolled steel coil multi stand forming unit into round pipe at room temperature, which is called indirect square forming process. The traditional roll forming process uses the method of fixed bending point position and variable bending radian to complete the corner forming of pipe blank, which is suitable for rolling small and medium-sized products. Rolling with this process & ldquo; Superb & rdquo; Square tube will show its inherent defects. Because the roll work in the bending process of this process is always concentrated at the point excessive stress concentration often shows microcracks in the bending process of profiles, which will lead to cracking in serious cases. The products with such defects have serious consequences when they are used in building steel structures. The study of the broken square tube column in the Hanshin earthquake in Japan shows that the corner microcrack is the main cause of the square tube fracture. At the same time, due to the different forming bending radians of products with different wall thickness, the universality of rolls is limited. The large-size cold-formed square tube used in the process adopts the advanced & ldquo; Direct Square & rdquo; The production process is to directly roll the hot-rolled steel coil into a square and rectangular shape at room temperature.The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Welding seamless welding seamless is to make welded elbows. After grinding and pickling, sand blasting, there is no sign of welding on the surface. Even using advanced flaw detection equipment,KingstonPrice of DN80 galvanized square pipe, it can not be seen that they are welded elbows.
After chemical pickling,Kingston40 galvanized square pipe specification, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube We only need to treat according to these, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel, resulting in electrode potential difference, so the steel surface treatment requirements are very high.Pile pipe and bridge; Pipes for wharf, road, building structure, etc. It is mainly used as petroleum geological drilling pipe, cracking pipe for petrochemical industry boiler pipe, bearing pipe, high-precision structural pipe for automobile, tractor and aviation, etc.The principle of straightening machine is that a disc is divided into two sides to clamp round steel straight lines. Professional square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, high price, service, on-site settlement, honest operation! The edge is one with radius r, and the center distance between them is adjusted to R + R + D.Potential development,The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~ which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized tubes, on-site settlement, honest operation, local offices, long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Compared with other welding, square pipe welding has many advantages, mainly because of the exothermic reaction, the material only needs to be heated below the melting point
According to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).superior quality,Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.Today, with the development of the world, all fields are coming rapidly, which makes the demand for square tube higher and higher, and the requirements of customers for square tube higher and higher. Now we are studying a new square tube. The following mainly introduces the performance of square tube in tensile strength.Stainless steel square tube for fluid transportation (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.Kingston,The second is the pickling of the square pipe. Both chemical and electrolytic methods are used when pickling the square pipe. These two methods can remove the oxide skin of the square pipe.Square tube plays an important role in the rapid economic development. The functions of square tube are different, and its characteristics are also different. Square tube has strict standards. There are many welding processes and advantages of square tube. Let me show you the welding process and advantages of lower tube.Reinforcing phases such as reinforcing particles, short fibers and whiskers can be added to the solder to form composites.
share 3 Comments
Comment / Cancel reply