category：Machinery and industry equipment / date：2024-03-23 00:06:21 / browse：39 / comment：6
When using the boarding bridge for loading and unloading, and do not be overweight. If overweight occurs, it will make the hydraulic system struggle during the lifting process, and even cause deformation of the hydraulic cylinder body, resulting in gaps and oil leakage outward. This requires finding a professional manufacturer for maintenance, such as Shanghai Niuli Machinery. If the deformation is severe, the only option is to replace it with a new one.In general there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder, etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes, sand holes, and shrinkage porosity in the guide sleeve.poland,The use of imported seals ensures excellent sealing performance of the hydraulic system.Anti collision block: This device can effectively protect buildings and boarding bridges from damage.Trebisov, . Platform side boarding bridge: The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages.The problem of sealing ring damage is common in almost all hydraulic systems, such as oil cylinders. It may be due to poor quality of the sealing ring itself, insufficient compression of the sealing ring, etc. When the sealing ring is lifted and lowered for a long time, it causes varying degrees of wear and tear on the sealing ring. This is a common cause, leading to gaps in the sealing performance of the sealing ring,polandFixed electric hydraulic boarding bridge, resulting in oil leakage. At this time only the damaged sealing ring needs to be found, Just replace it with a new one.The instrument equipment instrument inspection (inspection and testing) method utilizes various instruments to measure the hydraulic system, hydraulic components' performance (xì ng né ng), parameters, and analyze and process these data (ch ǔ l ǐ) To determine the location of the fault. A mature lifting platform manufacturer in China, with complete products and quality assurance.
Secondly, the selection of hydraulic pump stations and oil cylinders for fixed hydraulic boarding bridges is also crucial. These equipment are central components of external equipment and cannot be ignored. This not only determines the long-term use of fixed hydraulic boarding bridges, but also the inability to support the entire operation process!Install anti rolling foot skirts on both sides to prevent accidental injury to the toe platform.Insufficient understanding of the operating conditions of the axle. Assuming you understand some fundamental principles and the three elements that lead to success, you can ensure that you are in excellent working form for a long time. Inspection before use of mobile boarding bridge: Check if the oil unloading valve is tightened. Use of mobile boarding bridge: Use a hand pump to raise the boarding bridge to the required position and height; Place the tongue plate on the box and connect the safety chain to the box; Place the wheel mask in a suitable position next to the tire; Release the manual oil unloading valve to make the oil cylinder and wheels in a natural state, making them in a relaxed state; After the above preparations are completed, loading and unloading can begin; Precautions for operation: Keep the oil cylinder in a relaxed state during use; Both electric and manual lifting must turn off the manual pump switch.Inspection standard, there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder, etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes, sand holes, and shrinkage porosity in the guide sleeve.The instrument equipment instrument inspection (inspection and testing) method utilizes various instruments to measure the hydraulic system, hydraulic components' performance (xì ng né ng), parameters, and analyze and process these data (ch ǔ l ǐ) To determine the location of the fault. A mature lifting platform manufacturer in China, with complete products and quality assurance.Insufficient understanding of the operating conditions of the axle. Assuming you understand some fundamental principles and the three elements that lead to success, you can ensure that you are in excellent working form for a long time. Inspection before use of mobile boarding bridge: Check if the oil unloading valve is tightened. Use of mobile boarding bridge: Use a hand pump to raise the boarding bridge to the required position and height; Place the tongue plate on the box and connect the safety chain to the box; Place the wheel mask in a suitable position next to the tire; Release the manual oil unloading valve to make the oil cylinder and wheels in a natural state, making them in a relaxed state; After the above preparations are completed, loading and unloading can begin; Precautions for operation: Keep the oil cylinder in a relaxed state during use; Both electric and manual lifting must turn off the manual pump switch.
The fixed boarding bridge of the service platform is immediately installed on the outer edge of the unloaded service platform during the entire installation process. When applied, there is no need to excavate or pre bury the indoor space of tunnel construction on the loading and unloading platform, and most of the buildings do not need to be modified in terms of structure.Design brand,Of course, due to frequent shipments, long operation time, the quality of fixed hydraulic boarding bridges has been greatly tested. Based on market analysis, the editor above provides some suggestions to enemies who have used fixed hydraulic boarding bridges, and pays attention to some achievements in the application process.Regarding the year-end maintenance of the boarding bridge, check all hydraulic pipelines and joints to ensure that they are not damaged or loose. All joints must be tightened; Discard all hydraulic oil and replace it with new oil to avoid continuing to use old oil. Otherwise, the moving components in the system will accelerate wear and tear. Remove and disassemble the lowering valve, blow out the plunger with compressed air, and then reinstall it. To use a fixed hydraulic boarding bridge, it is necessary to have a basic understanding of its basic knowledge. Below, Jinan Zhongding Elevator will analyze it for everyone: To operate a fixed hydraulic boarding bridge, first open the rear door of the truck, fix it on both sides of the carriage, brake the truck. Turn on the power switch on the electric control box, and the professional boarding bridge factory has stable, safe, reliable,polandMobile hydraulic boarding bridge, and can achieve maintenance free performance. The technical level has reached the domestic level and the international advanced level of similar productsThe problem of sealing ring damage is common in almost all hydraulic systems, such as oil cylinders. It may be due to poor quality of the sealing ring itself, insufficient compression of the sealing ring, etc. When the sealing ring is lifted and lowered for a long time, it causes varying degrees of wear and tear on the sealing ring. This is a common cause, leading to gaps in the sealing performance of the sealing ring,poland10 ton mobile boarding bridge, resulting in oil leakage. At this time, only the damaged sealing ring needs to be found,Vibration acoustic method: Vibration acoustic instruments detect the vibration and noise of hydraulic systems, and identify the wear (a basic type of component failure) and technical status of hydraulic components according to the laws of vibration acoustics. Based on this, diagnose the cause, location, degree, nature and development trend of faults. Nowadays, with the rapid development of the logistics industry, the demand for logistics equipment is becoming increasingly weak and auxiliary improvements such as fixed hydraulic boarding bridges and fixed lifting channels, as well as the increase in loading and unloading equipment usage, have been made. Some manufacturers have now achieved export to foreign countries!The overall module of the water inlet pipe of the hydraulic boarding bridge must have a reasonable hydraulic system during the application process, so that the equipment has excellent airtightness and a long service life, and the height of the equipment is fixedAccording to the introduction of information, about % of the faults in the fixed axle hydraulic system are caused by oil infection. Therefore, various analysis methods are used to identify the composition and specific gravity of pollutants in the oil, which can diagnose the faults and degree of hydraulic oil pollution in the fixed axle hydraulic system. The car mounted hedge trimmer improves the trimming quality, saves labor, improves work efficiency, and has a times higher rate than manual trimming, without any safety hazards; Can form different plant shapes. Used for pruning road greening plants.
share 6 Comments
Comment / Cancel reply