BludenzDifference between laminate floor and solid wood composite floorAnalysis and application of preparation before replacement / 15303content

category：Environmental protection / date：2024-01-26 04:26:24 / browse：66 / comment：6

I have seen the evaluation video before. Netizens rub the steel ball of cleaning tableware back and forth on the SPC floor, and there is no trace on the surface.If it&#;s a wooden floor, I think it&#;s not like it anymore. You can see how good its wear resistance is.Secondly, the wear resistance is several times that of ordinary floor.Bludenz,BludenzTop 10 brands of wood flooring,Briefly describe several common wood varieties:Foot feelBac Giang,SPC ground anti-skid, and the ground anti-skid shall meet the European standard RBecause of the low thermal conductivity and excellent anti-skid performance of the ground, compared with ordinary floor tiles and marble, SPC floor feels astringent when sticking water and is not easy to roll. Therefore ground building decoration materials are preferred in public places with high safety regulations, such as toilets, showers, hospitals, kindergartens, medical management centers, rehabilitation hospitals, colleges and universities, which are very popular in China in recent years. Defects.How to buy solid wood composite flooring?

As the wear-resistant layer on the surface of the laminate floor has good wear resistance, compression resistance, impact resistance, fire resistance, flame retardancy and chemical pollution resistance, in daily use, it only needs to be cleaned with a twisted dry rag, mop or vacuum cleaner. If the floor is greasy and dirty, wipe it with a cloth stained with detergent. Wear resistant.SPC floor adopts special transparent wear-resistant layer processed by high technology, look at the priceExcellent service, Considering from the elements of economic development: strengthening is better than solid wood.If you buy solid wood the quoted price is generally the price of bare board, plus the price of installation and spare parts. In terms of comfort, strengthening and solid wood are better than ceramic tiles, because they are warm for many days and cool in summer.In addition to the high wear-resistant solid wood floor, the electronic organ architectural coating floor is also the main product in the recent popular sales market.Beautiful and bright appearance, with super thick wear-resistant layer, and the upper foot is stronger. The appearance is very similar to the solid wood floor, but the price is far less than the solid wood floor.The solid wood composite floor is overlapped and laminated by the boards of different greening plants, which gets rid of the defects of wet expansion and contraction of the solid wood floor to a certain extent. The dry shrinkage and wet expansion rate is small, the specification stability is good, thorough vacuuming will make the rest of the work easier.Ask the installer in advance whether to remove the old floor or decide by himself.

The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Excellent service, Beautiful and diverse colors,BludenzHow to choose laminate flooring, seamless splicing construction convenient and fast installation.Therefore, when insects appear on the wooden floor, we should first find out where they are born. Only by manipulating the insect source can we reasonably kill insects. LookBludenz,The standard laminate floor surface should contain aluminum oxide wear-resistant paper. It has g, g,BludenzWood floor insect, g, and even lower. It is directly sprayed with aluminum oxide on the decorative paper. The state stipulates that the surface wear-resistant revolution of the laminate floor for indoor use should be more than revolutions. Only the floor with g wear-resistant paper can meet the requirements. The wear-resistant revolution of g wear-resistant paperThe number of revolutions can reach -, or even lower than g. It is good if the number of revolutions directly sprayed with aluminum oxide can reach -. For those with low wear-resistant revolutions, the material cost is relatively low; because of its low wear-resistant degree, the tool cost during processing is also low. On the contrary, the cost is much higher if the number of wear-resistant revolutions is high.Advantages: high wear resistance, good reliability moisture-proof, rich and colorful color and pattern design types, and large price range.In addition, pay attention to whether there are sawdust and stratification on the cutting surface of the plate and whether there are sawdust and stratification on the cutting surface of the solid wood floor.